User Controls
Posts by ssss
-
2022-06-13 at 6:38 AM UTC in how i clean my pills ?
Originally posted by the man who put it in my hood You can distil xylene from laquer thinner. But laquer thinner is actually REALLY GOOD for cleaning pills, some people swear by a LT preboil but it needs the ethyl acetate to be of any use because that shit is gnarly to pill fillers it loosens them up and makes the pill gunk matrix easier to attack with xylene. Toluene might work for a main boil solvent but not as well I don't think it has the best properties
Don't use water. If water or LYE or a strong base touch the pills it will activate the hidden government antimethcook chemicals that turn the entire mass into a pile of jello that wouldn't dissolve in boiling strong acid and you gotta throw it out and start from scratch
That's why you need to use a weak base like sodium carbonate which can be made easily from baking powder and a oven. 99% of meth cook guides were written before this was a thing so they say USE LOTS OF WATER AND RED DEVIL LYE AND SHAKE SHAKE SHAKE BABY but if you try that now in 20XX you will probably just make a mess
I'm not in usa and I'm using pills from local company so i don't think there's any antimethcook chemicals so i putted
one pill in water and did dissolve completely and i did evaporate the water and didn't fined anything unusual so is there any test that i can do to the pills to be sure and about the SODIUM METAL i have like 100g so I'm fine and i will use Ammonium sulfate for the anhydrous ammonia all whats is left is the pills -
2022-06-12 at 4:14 AM UTC in how i clean my pills ?
Originally posted by the man who put it in my hood how can you not find solvents isn't there a HARDWARE store like Lowes?
You just gotta BOIL it in XYLENE the trick is to use a weak base like SODIUM CARBONATE to liberate the hcl bond from the salt and then boil in xylene to remove it from all the crap and enhancement it out dissolved in solvent because the plastic and wax and filler doesn't dissolve and then you gas it and clean it up its a tried and true method called the tetra twist with preboil
you also need tetra
" Combine approximately the same volume of sodium carbonate as unground pill volume: put the pills in the blender, grab a handful of carbonate and toss an eyeballed estimate on top of the pills. A reasonable approximation for 1 box of 96 30mg “red hots” would be about 2.5- 3 tablespoons. Cover the blender, run on high for about 1 minute. Let stand 5 minutes before removing lid.
2. pour the powder created in step 1 into a dry glass beaker – the dry pill mass should not be more than 1/3 of the beaker volume.
3. Carefully hose the powder-in-beaker from step 2 with tetrachloroethylene straight from the can. Hint: direct the stream to the upper part of the beaker onto the glass wall to prevent scattering your dry pill mass. Otherwise, spray the tetra in a glass first, then pour into the beaker. Saturate the pill mass: this means that all of the powder should be wet, but there should be no free-running tetra. Tip the beaker just to make sure that the tetra doesn’t run. The mass should be one glorious whole. If you added to much tetra, the application of heat at this point is prudent – not only to evaporate the extra tetra, but to drive the tetra into the powder more thoroughly. 120mg pills can soak up quite a bit of tetra, so saturate, heat, and add more tetra until you reach this point of saturation. Extra tetra can be soaked up easily from the top of the pill mass with a couple of cotton balls.
4. pour toluene into the beaker until the level of toluene is approximately 1” above the pill mass. This will vary with the overall magnitude of the extraction you are performing – experiment with 3 boxes of 96, using this one-inch approach. You have the option of using VM&P naphtha at this point instead of the toluene – in the precipitation stage, you’ll chill the naptha to crash the crystals. You’ll evap the toluene. Evaping hydrocarbon solvents is nasty business. Just ask Geez. The naptha chill takes 1-2 hours, possibly endangering your position. Your pays yo’ money, you takes yo’ shot.
5. add a dash of water. (for 3 boxes of 96, use 2 tablespoons). Start with little h20 – you can always add more toluene and another shot of h20 if you want to try another pull. You’ll screw the whole gig if you add too much h20 for the first pull.
6. Apply heat gently while stirring until the contents of the beaker are at the boiling point, then back off. Practice makes perfect. Keep the temperature just below that boiling point for 2 minutes (4 minutes if using 120mg 12-hour pills). Stir continuously with appropriate implement.
7. Remove beaker from heat source and let settle for 1 minute.
8. decant all liquid from beaker into a suitable heat-resistant glass pan, bowl, etc. Visionware rules the roost. You may choose to decant through a enhancement/funnel, or just keep a cotton ball at the lip of the beaker as you pour.
9. Evap the toluene on low heat for clean crystals easily lifted. Or if using VM&P naphtha, place in freezer for 2 hours, enhancement, and place the crystals on a coffee enhancement to dry. "
can i use Kerosin or i should Extract Toluene or XYLENE From Lacquer Thinner . i cant fined tetra so i have to get it from BRAKE CLEANER so can i use water or any common solvent as first step to reduce pills mass then dry theme and do you method so i can use less solvents or its useless -
2022-06-10 at 6:43 AM UTC in how i clean my pills ?hi i want to clean my pills for birch reduction so i need help with that but its hard to fined solvents here
i'm not in the usa or any country with heavy laws against drags so i don't think there's hidden ingredients but how to check
my pills contain :
pseudoephedrine hcl bp
triprolidine bp
(what bp means) ?
and as an excipients :
maize starch
anhydrous lactose
microcrystalline cellulose
croscarmellose sodium
colloidal anhydrous silica
magnesium stearate -
2021-04-15 at 12:11 PM UTC in How to learn to cook meth Part 1 - The Shake and Bake.1
-
2021-04-09 at 12:33 AM UTC in How to learn to cook meth Part 1 - The Shake and Bake.1
-
2021-04-08 at 8:19 AM UTC in How to learn to cook meth Part 1 - The Shake and Bake.1