User Controls

Muh BRAKES! Help me space niggas 🚙

  1. #1
    Fonaplats victim of incest [daylong jump-start that nome]



    Fucking why it doing this?
    How I fix?
    Plz thanks god bless
  2. #2
    If they're working OK don't worry about it, looks like the pads are fucked up and either unevenly worn or not closing right and need replacing but it's not a big deal.
  3. #3
    Fonaplats victim of incest [daylong jump-start that nome]
    Originally posted by Donald Trump If they're working OK don't worry about it, looks like the pads are fucked up and either unevenly worn or not closing right and need replacing but it's not a big deal.

    I just replaced them last month.
    Don't you take a bus?
  4. #4
    stl1 Cum Lickin' Fagit
    Originally posted by Fonaplats I just replaced them last month.



    I think we have identified the problem.
  5. #5
    Originally posted by Fonaplats I just replaced them last month.
    Don't you take a bus?

    well then it means YOU FUCKED UP.

    you probably didnt lube the screws.
  6. #6
    stl1 Cum Lickin' Fagit
    And, Vinny would know about lube.
  7. #7
    Give them time to bed in. You obviously have uneven wear somewhere. Next time maybe change the rotors.
    The following users say it would be alright if the author of this post didn't die in a fire!
  8. #8
    Originally posted by stl1 And, Vinny would know about lube.

    yes.

    im not surprised your ignorant of them.
  9. #9
    Originally posted by Donald Trump Give them time to bed in. You obviously have uneven wear somewhere. Next time maybe change the rotors.

    its obvious from the pict that the calliper mounting is bent.
  10. #10
    BeeReBuddy motherfucker [pimp your due marabout]
    Originally posted by vindicktive vinny its obvious from the pict that the calliper mounting is bent.

    Fuck my dick
  11. #11
    BeeReBuddy motherfucker [pimp your due marabout]
    Originally posted by vindicktive vinny well then it means YOU FUCKED UP.

    you probably didnt lube the screws.

    Lube the screws?
    GOD DAMN IT!
  12. #12
    AngryOnion Big Wig [the nightly self-effacing broadsheet]
    I know what's wrong.
    Post it when I have time.
    The following users say it would be alright if the author of this post didn't die in a fire!
  13. #13
    cigreting Dark Matter
    take the pins out and lube/sand the rust off them
    The following users say it would be alright if the author of this post didn't die in a fire!
  14. #14
    BeeReBuddy motherfucker [pimp your due marabout]
    I didn't use lube and I noticed little boots on the pins and 1 had failed.
    It is a 20 year old car and Ill probably just use the next stimi to buy a van.
  15. #15
    cigreting Dark Matter
    Hope you replaced the rubber piece
  16. #16
    Those brakes look fine though. It's just due to the pad wearing faster at the outside than the inside because that's how circles work - the outside moves faster and shit.
  17. #17
    aldra JIDF Controlled Opposition
    what exactly is happening? they look old but not in particularly bad condition
  18. #18
    BeeReBuddy motherfucker [pimp your due marabout]
    Rotor shouldn't be rusty where it is rusty.
    Clearly I an inhibited in my current braking abilities.
  19. #19
    AngryOnion Big Wig [the nightly self-effacing broadsheet]
    Originally posted by cigreting take the pins out and lube/sand the rust off them

    Its not just the pins it is where the pads sit in the caliper hanger,those groves have to be cleaned down to bare metal and then they need some slide grease or anti-seize put in there.
    Don't put a ton in just enough to keep it from rusting up again.
    Also make sure the pins slide through the pin hole easy-you don't want it super tight like a virgin.
    If it is then you have to pull that rubber sleeve out and clean the rust out of the hole it was in.
    The rubber sleeve can be hard to get out but I have found that the best way is to get a thin longish flat blade screw driver and slide down the side of the rubber sleeve,once you get all the way down push the screwdriver to the center of the sleeve then you can twist the thing out.
    Then scrape the rust out of the hole put lube on the inside and outside of the sleeve and reinstall in the caliper.
    Then recheck how the pin moves.
    That should fix it.
    The following users say it would be alright if the author of this post didn't die in a fire!
  20. #20
    AngryOnion Big Wig [the nightly self-effacing broadsheet]
    Originally posted by cigreting Hope you replaced the rubber piece

    That is something you should do but hardly anyone does.
    I have seen it so many times even at a dealership level they just bang that shit out as fast as possible and hope for the best.
Jump to Top